$2 for 5PCBs - order with coupon code: JLCPCBcom
Any questions about JLCPCB or ordering, pls email support @jlcpcb.com
More electronics bits and pieces from the UK and China.
Interested in my new garden workshop? Follow the entire build on Julian's Shednanigans:
https://www.youtube.com/channel/UCXfDjPehpC7B7lW2JFxeS4w
12pcs 400V 10A 12 Position Fork Relay Short Circuit Strip Barrier Terminal Block https://ebay.us/OozwIP
5Pcs 600V 15A 4 Positions Barrier Strip Terminal Block Wire connector TB-1504 https://ebay.us/LIFj3B
Digital DC-DC Voltage Regulator Buck Converter 12A 720W Step Down Transformer #Unbranded https://ebay.us/f2HRFs
Vintage E27 B22 LED Edison Bulb 3W 4W 6W Retro Home Lights Lamp 12V 85-265V RL #Ranpo https://ebay.us/kO4xqn
Screw ES E27 to Bayonet BC B22 Converter Light Bulb Fitting Holder Pin to Screw https://ebay.us/jVZMyR
Any questions about JLCPCB or ordering, pls email support @jlcpcb.com
More electronics bits and pieces from the UK and China.
Interested in my new garden workshop? Follow the entire build on Julian's Shednanigans:
https://www.youtube.com/channel/UCXfDjPehpC7B7lW2JFxeS4w
12pcs 400V 10A 12 Position Fork Relay Short Circuit Strip Barrier Terminal Block https://ebay.us/OozwIP
5Pcs 600V 15A 4 Positions Barrier Strip Terminal Block Wire connector TB-1504 https://ebay.us/LIFj3B
Digital DC-DC Voltage Regulator Buck Converter 12A 720W Step Down Transformer #Unbranded https://ebay.us/f2HRFs
Vintage E27 B22 LED Edison Bulb 3W 4W 6W Retro Home Lights Lamp 12V 85-265V RL #Ranpo https://ebay.us/kO4xqn
Screw ES E27 to Bayonet BC B22 Converter Light Bulb Fitting Holder Pin to Screw https://ebay.us/jVZMyR
what is function of it ?
I've got a few as well . I tend to treat them delicately .๐คฃ
You will burn your shed down with all that wiring!
Hi Julian, faced with an accumlation of various parts, I'm curious how you organize all these parts you receive. What system/method do you use to organize your parts? Can we have a glance at your setup?
yay no reply ๐
I realy do love your bostbag Videos. Keep the good work up Julian ;D
> Uses break-off knife
> complains about bluntness
I don't think it's possible to be any more British than that.
Why don't you break the old blade tip off, then you will have a sharp knife again…
I would consider that power supply a pain in the @#$s to use.
The system they have there will lead to some major equipment fails due to incorrect output settings because it is not clear what you are fiddling with.
Why not have a decent display and rotary encoder and some up and down buttons.
$28 US = $39 AUD, and the shipping would not be free. Sorry not worth it.
I was just wondering, would the DC-DC converter output stay a constant voltage for a variable input voltage i.e from solar panels?
How does someone drag out opening mail, loves the sound of his own voice.
Why not just put two positives next to each other and then two negative next to each other thereby not having to break off any of the tabs?
As in…Positive to #1 & #2 and Negative to #3 & #4.
Why use 4 with 2 forks broken off? 3 with middle fork broken off does the same and saves 1 fork
ProTip: Halogen lamps are designed to run at their full voltage. Running them at a lower voltage will shorten their life. It has something to do with how the high temperature "boils" the top layer of metal off of the filament and then the metal is attracted back to the filament again. Operating the filament at a lower temperature does not allow this process to work correctly and the filament is prone to early failure.
Before putting high voltage on the input, verify the voltage rating of the input cap(s). I've seen a lot of chinese gear which claims higher input voltage than the actual capacitor rating. It'll work for a little while if you don't exceed the rating by too much…
Just a guess on the buck … set the parameters. Go to P-0 (program-0). Press and hold a button to save them? Maybe even a temporary set by holding the ON button. Just guessing.