A selection of items from ICStation.com
AD9833 DDS Signal Generator Module 0-12.5MHz Square/Triangle/Sine Wave
Item ID: 7186
http://www.icstation.com/ad9833-signal-generator-module-125mhz-squaretrianglesine-wave-p-7186.html
Single-Supply To Dual Power Switch Module DC-AC Car Tone Power
Item ID: 7665
http://www.icstation.com/single-supply-dual-power-switch-module-tone-power-p-7665.html
Innovative Universal Double Side Board PCB 9x9cm 2.54mm DIY Prototype Paper PCB
Item ID: 7191
http://www.icstation.com/innovative-universal-double-side-board-9x9cm-254mm-prototype-paper-p-7191.html
Note: Some items in this video were supplied at no cost.
AD9833 DDS Signal Generator Module 0-12.5MHz Square/Triangle/Sine Wave
Item ID: 7186
http://www.icstation.com/ad9833-signal-generator-module-125mhz-squaretrianglesine-wave-p-7186.html
Single-Supply To Dual Power Switch Module DC-AC Car Tone Power
Item ID: 7665
http://www.icstation.com/single-supply-dual-power-switch-module-tone-power-p-7665.html
Innovative Universal Double Side Board PCB 9x9cm 2.54mm DIY Prototype Paper PCB
Item ID: 7191
http://www.icstation.com/innovative-universal-double-side-board-9x9cm-254mm-prototype-paper-p-7191.html
Note: Some items in this video were supplied at no cost.
can not find your video where you compare ad9833's
That last item sounds like a "kit" of several parts they needed to get rid of. 😄
I hope "Alice" is still good to you. 🙂 (If anyone is up in arms, XMOS would be blasphemy). Think about it.
Merry Christmas and Happy New Year Everyone.
Cheerio to you too, sir. 🙂 Hope you are well for the Holiday Season (ChristMOS) and the New Year. 2019. Wow.
Carry on, Good Chap! (You can tell I'm from the USA, huh). You are great. I've got great things to say about Alice. Awesome.
Just an interesting thing: when you sad "ac" siri come on my iphone a couple times 😂😂😂
on the page you were on it said a power module for a Spherical Lamp
Just an FYI. Your Ryobi Tek 4 DVM's will only read AC voltage accurately between 40HZ – 400HZ. Check the Specs. Most DVM's will only read AC voltage accurately between that frequency range. 50hz for Europe, 60HZ for US and 400hz for military gear. That is most likely the reason you are getting such low readings on the output of the DC to AC module with your DVM's.
JULIAN!!! You've done it this time… darn near literally rolling on the floor laughing when you started measuring that DC -> AC module. AC doesn't have a ground like DC does! Think of your mains – ground is just earth, to protect the case. You should have been measuring the two outer AC connections with the one DVM set to AC. And your scope, I expect you would just connect one probe to one AC terminal, and the other to ground, and changed your coupling to AC, and you'd get your AC sine wave. And you were cheated on those PCBs… the eBay ones come with 2x1k, 2x10k, and 2x3k… just to confuse 😉
Oh, and as far as the soldering goes… I'd be looking for some different solder – some of the cheap 60/40 solder isn't really 60/40, or cheaps out on the flux.
l.&, ←◇:-)♧♧↓♧) 3.
Never been to ICstation, and it looks like I won't be going either 😉
Thanks for bringing us into the workshop Julian .
Ignore the nay sayers, unfiltered idiots on the internet….you know.
looks like a bus board, take power jack, rj45, db9, some take more footprints on both sides.